Debugging Qt Quick Projects

Setting Up QML Debugging

The process of setting up debugging for Qt Quick projects depends on the type of the project: Qt Quick UI or Qt Quick Application, and the Qt version used. To debug Qt Quick UI projects, select the Enable QML check box in the Debugger Settings in Projects mode Run Settings.

To debug Qt Quick Applications:

1. If you use qmake as the build system, make sure that debugging is enabled in the Build Settings, QML debugging and profiling field, either explicitly for the project or globally by default.

   

   Note: Debugging requires opening a socket at a TCP port, which presents a security risk. Anyone on the Internet could connect to the application that you are debugging and execute any JavaScript functions. Therefore, you must make sure that the port is properly protected by a firewall.

2. In the Run Settings, Debugger Settings section, select the Enable QML check box to enable QML debugging.
3. Select Build > Rebuild Project to clean and rebuild the project.
4. To debug applications on devices, check that Qt 5.0, or later, libraries are installed on the device and select the corresponding kit for the device before you start debugging.

Mixed C++/QML Debugging

To debug both the C++ and QML parts of your application at the same time, select the Enable C++ and Enable QML checkboxes for both languages in the Debugger Settings section in the project Run Settings.

Starting QML Debugging

To start the application, choose Debug > Start Debugging > Start Debugging of Startup Project or press F5. Once the application starts running, it behaves and performs as usual. You can then perform the following tasks:

• Debug JavaScript functions
• Execute JavaScript expressions to get information about the state of the application
• Inspect QML properties and JavaScript variables and change them temporarily at runtime

To debug already running applications:

1. Build the application by using the appropriate configuration parameters (if you build the application with Qt Creator, it automatically uses the correct configuration):
   • When using CMake, the target_compile_definitions command is defined in the CMakeLists.txt file: target_compile_definitions(myapp PRIVATE QT_QML_DEBUG)

     Where myapp is the application to debug.

   • When using qmake, the following value is defined for the CONFIG property in the .pro file: CONFIG += qml_debug
2. Start the application with the following arguments:

   qmljsdebugger=port:<port>[,host:<ip address>][,block]

   Where port (mandatory) specifies the debugging port, ip address (optional) specifies the IP address of the host where the application is running, and block (optional) prevents the application from running until the debug client connects to the server. This enables debugging from the start.

   Note: Setting breakpoints is only possible if the application is started with block mode.

3. Select Debug > Start Debugging > Attach to QML Port.

   Choose the kit configured for the device where the application to be debugged is running. The port number to use is displayed in the standard output when the application starts.

Debugging JavaScript Functions

You can use the Qt Creator Debug mode to inspect the state of your application while debugging. You can interact with the debugger by:

• Setting breakpoints
• Viewing call stack trace
• Viewing local variables and function parameters
• Evaluating Expressions

Inspecting Items

While the application is running, you can use the Locals view to explore the QML item structure.

To keep the application visible while you interact with the debugger, select Debug > Show Application on Top.

You can view a QML item in the Locals view in the following ways:

• Expand the item in the object tree.
• Select the item in the code editor.
• Select Debug > Select to activate selection mode and then click an item in the running application.

To change property values temporarily, without editing the source, double-click them and enter the new values. You can view the results in the running application.

Inspecting User Interfaces

When you debug complex applications, you can jump to the position in code where an item is defined.

In the selection mode, you can click items in the running application to jump to their definitions in the code. The properties of the selected item are displayed in the Locals view.

The Select tool will be enabled either if your application is using Qt 5.7 or later, or if your application is using an earlier version of Qt and is based on the QQuickView class. You can also view the item hierarchy in the running application:

Double-click an item in the running application to cycle through the item stack at the cursor position.

To switch out of the selection mode, toggle the Select menu item.

To move the application running in Qt QML Viewer to the front, select Debug > Show Application on Top.

Executing JavaScript Expressions

When the application is interrupted by a breakpoint, you can use the QML Debugger Console to execute JavaScript expressions in the current context. To open it, choose View > Output > QML Debugger Console.

You can change property values temporarily, without editing the source, and view the results in the running application. You can change the property values permanently in code.

Applying QML Changes at Runtime

When you change property values in the QML Debugger Console or in the Locals or Expression view, they are immediately updated in the running application, but not in the source code.